Questions

Filter by Topic
All
  • All
  • Anchoring (STRONG & SOLO Models)
  • Inertia Wave SOLO
  • Inertia Wave DUO
  • Inertia Wave STRONG
  • Purchasing
  • Product Care

Need more help?

If none of these topics are helpful to you, please contact us using the bottom at the bottom of this page.

If you have an issue or question that requires immediate assistance, please call us at 203-675-5575 to speak to support.

Anchoring (STRONG & SOLO Models)

If you clip caribiner to any object you will lose over 35% of the feed back, impedence match response. Please never omit rail strap. Never clip carabiner to any object. Micro trama it will break. It will also increase force loads to the end caps of the STRONG MODEL;. Use at your own risk when modifying the Inertia Wave.

Yes! If you omit the Rail Anchors to make up for space, you will lose energy in the tubes and weaken the O-ring. If you hook the carabiner directly to your anchor location it will tear on the O-ring, and will increase torque stress throughout the entire tube. The product will break, will not last. Your Inertia Wave will perform at 100% and last twice as long with the Rail Anchor, carabiner, and O-ring. Note: It will perform optimally... The carabiner always sits in between the D-ring of the Rail Anchor, and the O-ring of the Inertia Wave.

These features are part of the Rail Anchor and are used securely anchor the Inertia Wave. The combination of these components help to alleviate the stress, wear, and torque on the anchored end of the Inertia Wave by creating a "stress curve". For best results and a longer lasting Inertia Wave, you MUST keep the Rail Anchors as extended as possible - do not wrap the Rail Anchors around objects repeatedly to shorten its length. The longer the strap, the less strain on the O-ring and tubes.

As shown in the "Creative Ways to Anchor the Inertia Wave" video, the anchor points should be a minimum of 36-40 inches from ground at waist height, and between 24-36 inches apart. Please remember to always use your Rail Anchors.

The proper way to anchor using the Rail Anchors is to keep it flat, wrap it tightly around 24 to 36 inches apart. Now feed the D-ring through the opening loop of the nylon strap and pull it tightly three times. Make this connection as snug as you can to the point where the strap cannot slide up or down as you utilize the Inertia Wave. Attach the carabiner to the D-ring of the Rail Anchor, and the O-ring of the tube. Make sure the carabiner is completely closed before use. Do NOT attach the Rail Anchors to any sharp or jagged objects. Be sure to use as much of the Rail Anchors as possible - do not shorten or modify (see above).

No, the Door Anchors are designed to handle stress being as locked into place as possible. If you use the Door Anchors on doors that do not have hinges, you may destroy the Door Anchor or damage your door.

THE INERTIA WAVE IS 100% CORE & CARDIO - far superior to any core cardio exercise known today (MIT), it’s all posterior- sends dynamic feedback & kinetic energy into your entire body. World records are an average of 60 seconds out, all-out, non-stop wind sound (See anchor videos) Did you happen to see the email that came to you within five minutes of purchasing the INERTIA WAVE… (from Help@Inertiawave.Com ) It contains everything you need in regards to the methods and proper anchoring. Please check your inbox and spam/trash folders. ▶️The links are Beginners methods of use” & “Advanced methods of use... as well as the STRONG WORKOUT. Depending on which model you purchased, there is a corresponding video link/s If you have the SOLO or STRONG, watch every link, omitting the DUO link. Practice & master the methods, understanding body position, torque/tension on the tubes, and keep the feet no more than 12 inches apart. Etc. etc.… Remember, if you don’t hear a massive wind sound, no matter what wave pattern you know, you’re not doing it correctly. You need to walk back, shake the water off your hands, and create more tension. Everything is explained in the videos. ▶️Once you feel comfortable with the different methods of use in the right body position, with the right tension on the tubes, anchoring the device properly… Now go to the “advanced methods,” there are 18. Now you can go to INERTIA WAVE on Instagram “official page”, only make sure it says Inertia Wave official page… You can see some of the workouts we are posting. You can also #INERTIAWAVE ➡️💥MORE ON HOW TO USE THE INERTIA WAVE? You are creating waves of motion, whether transverse or sagittal/ Via the Methods of Use video. You can use it as a warm-up, during metabolic conditioning, or high-intensity interval training, or use it as a cool-down; it all depends on the intensity & your perceived rate of exertion. ☑️Think of the Inertia Wave as a jumping rope that engages your entire body. It’s part of a circuit - it is an intense one! literally an extreme cardiovascular bout which has extreme demands over a 30 to possibly 60 second window. Ask yourself, if you went all out, how long can you jump rope without getting winded? Use it the same way - watch both video links, including the beginner's methods and advanced methods of use, and see if you can increase your time as you improve your stamina and cardiovascular endurance. Everything is based on your perceived rate of exertion. How winded are you on a scale of one to 10?… Once you could master a method flawlessly at your full potential, then you try to transition from one METHOD to the next… continually doing this until you can get many methods in a specific time frame (WINDOW) Once you accomplish this, then you start adding lower body movement patterns, like a side, step back, lunge, pop squat, walking forward, walking back, Setting up markers on the floor and doing a figure 8 pattern where you walk forward then back through the center then around to the right then back through the center, etc. get very creative when it comes to upper body movement patterns as you’re trying to maintain a specific wave pattern. be creative! ☑️For beginners or kids, you could start with one tube and do the same methods...Whether you’re doing it inside, outdoors, or in your gym, it can be a “go-to station“ between exercises… Whether it’s weightlifting or just bodyweight exercises, the method used will target specific muscle groups, as shown in the videos. That’s where your creativity comes in… ☑️Master the different wave patterns. 1st all beginner method videos, advanced method videos… Ask yourself, can you pick four wave patterns and transition, and or segue each pattern without stopping? - Just slow down slightly and introduce the next method, keeping it rhythmic and coordinated. This is what’s happening with cognitive skills and functionality, which challenges the body tremendously… Moving from one method to the next without stopping. . If you have purchased our top model, our most popular model, the INERTIA WAVE STRONG. Now you have the ability to perform an endless number of strength training exercises by clipping the belts on and off for the lower body and other areas of the body… The hand grips for strength training exercises are positioned between the wave patterns. This is a form of high-intensity interval training. Do a few sets of let’s say back, take the hand grips off, and go right into your wave patterns. ☑️Go to our website to see all the video links under the appropriate Model. If you bought the WAVE solo you can follow some of the advanced and beginner methods… If you bought the Strong , you could follow the STRONG workout methods. As well as the SOLO. ☑️A form of high-intensity interval training (HIIT), Tabata, or metabolic conditioning is exactly why the device was created… It’s super effective, exceeding double the benefits of jump ropes and many forms of cardiovascular activity in an extremely short window of time. Additionally, on the homepage of the website where you ordered it, you can see the difference between the battle rope and INERTIA WAVE. INERTIA WAVE OFFICIAL PAGE IG

Inertia Wave SOLO

Length:
From the anchor point to your hands, you will need at least 12.5 feet in length.

Width:
For some of the most optimal methods of use, you will need at least 3 feet in width to your left, and 3 feet in width to your right.

Height:
For some of the methods of use, you will need at least a 7-8 feet ceiling height. (That would make you super-human)

A clearing of 4 feet from left or right- then put your 1st anchor- 2nd anchor 24-36 inches apart YOUR CHOICE. Then SKIP 4 feet - drill or screw in the next anchor…repeat this sequence.

We recommend, for your safety, never pulling or stretching any of the 3- Inertia Wave models longer than 40 inches. It’s not a bungee and it may lose its integrity if you use it like a resistance tube. ONLY the IW-STRONG model can be used that way.

Inertia Wave DUO

No. The Inertia Wave Duo was designed with a built-in "wrist safety strap" at each end of the tubes. If you try to tie the safety strap and use it as an anchor, the safety straps may rip out. The safety straps are strong enough to stop the end cap from flying towards your partner, however, cannot withstand 300-600 lbs. of oscillating torque which it produces. PLEASE do NOT attempt to anchor your Inertia Wave Duo.

Length:
From your partner's hands to your own, you will need at least 11.5 feet in length. To perform the Hurrican Walk method, you will need more space to walk forward and back.

Width:
For some of the methods of use, you will need at least 4 feet in width to your left, and 4 feet in width to your right.

Height:
For some of the methods of use, you will need at least 7 feet in height from the ground.

Although we urge you to get creative with your Inertia Wave products by coming up with unique custom methods, you should never use them as a resistance tube or bungee. It will loose its integrity and can possibly cause you harm. Only the Inertia Wave STRONG casn be used as a resistence tube.

The original Inertia Wave has a solid steel O-Ring built into it. If a user were to let go, it can become very dangerous. The Inertia Wave Duo has safety straps instead. The Inertia Wave Duo has been tested and quality controlled and approved safety straps.

It is the user's responsibility and the user's negligence for the causation of any injury. User must be aware of sweaty hands, surroundings, and anything that may harm spectators or yourself. It is mandatory on the Inertia Wave DUO that you wear safety straps at all times.

You will void all terms, and be held accountable for any injuries.

We recommend, for your safety, never pulling or stretching the Inertia Wave® DUO longer than 26 inches. It’s not a bungee and it may lose its integrity if you use it like a resistance tube.

Inertia Wave STRONG

The difference is the STRONG has a "LOOP" running through and around the end cap. (End Cap that fits in palm of hand) this loop provides attachable hand grips, and two black straps, for a complete upper, and lower body strength training program. The STRONG is 5 Inches shorter, and has a coefficency rating that allows to be stretched up to 60 inches.

Yes, every method of use you see under the Inertia Wave® SOLO beginner, and advanced an be performed in the same without the hand grips attached.

No, the Inertia Wave® STRONG has a LOOP on each tube which you attach the hand grips to. This LOOP does not allow the proper wave oscillations, wave lengths, and feedback response when the hand grips, or belts are attached. If you perform the methods of use using the hand grips, you will damage the strength of the loop, or have it pulled out completely.

NOTE: Also lose any feedback response.

Yes, get creative! If you create another exercise that works for you, we love that! Don't forget to share it on our Facebook (/InertiaWaveOfficial) and Instagram (@inertiawave) pages!

The Inertia Wave® STRONG has a different resistance profile than the SOLO and DUO because of the complexity of its structure. For strength exercises and core work while using the hand grips or padded belts, you are able to safely stretch the tubes up to 60 inches. Just perfom your stength exercises, however you can attach Belt around waist, run out 3 feet and run in place, or back, and forth.

Purchasing

Coupon codes are distributed in two ways:

On our website, Top Tool Banner, a pop-up on home page, Also, during the holidays. You can also see them on social media platforms be reps, and influencers.

There are three different ways in which you can check out:

Create an account and check out- You provide your name, email address, phone number, and a password. This will create a user account in which you can sign in and use to view or track your orders.Sign in and check out- If you already have a user account, you can click the "Sign in here" link and user your email address and password to Sign in. This will record your purchase to your account for you to view or track.Checking out as a guest- You provide your name, email address, and phone number without entering a password. This will NOT create a user account for you, but will continue with your purchase.

A 6.35% state sales tax will be charged on all orders sold in the US state of Florida, and where NESUS laws are followed. This will automatically be added to your order when you choose Florida as the billing state.

All orders are shipped using FedEx. You, the customer, get to choose which method of shipping you would like to use. Each method has its transit times and is priced by FedEx based on package dimensions, what zone your in, and total weight. Note: International orders are discounted 80% when using FedEx International Connect Plus. If you refuse to pay your country's VAT Tax, and abort the package, you will be charged a $40.00 return fee. Some shipments must be sent via the United States Postal Service if using a PO Box.

You can track the status of your order in two ways:

If you have created an account, you can sign in to see the status of your order in the "My Account" page.Once your order is shipped, you will receive an email. This email will contain a recap of your order and your FedEx tracking number.If none of the above applies to you, you can contact us using the methods below.

Absolutely. Your safety while using our website is always a priority. All credit card information is encrypted and processed by Shopify. No credit card information is stored within our system. Your personal information will never be distributed or sold to third parties. Please refer to our Privacy Policy for more information.

Yes, please view our RETURN POLICY for more information on returning your product for a refund?

If you purchase the wrong product (for example, the Inertia Wave SOLO versus the Inertia Wave DUO), the customer will be responsible for providing the return label. We will exchange, as long as the product is still sealed in bag it came in, and no markings, or used. We will cover the return shipping.

Product Care

The Inertia Wave and Inertia Wave Duo tubes should be cleaned using a damp cloth with water and a mild soap.

The lifespan of Inertia Wave and Inertia Wave Duo depend upon the amount of use and proper care. All Inertia Wave products (products that contain the Inertia Wave tubing) are warrantied for 90 days. We recommend inspecting the entire length of the Inertia Wave tubes after every use and replacing them annually to ensure the best possible performance.

Yes, you can use hand sanitizer on the tubes and hand grips of your Inertia Wave, however, the alcohol in the sanitizer can degrade, discolor, and can discolor or break down the polymer and may lessen the tensile strength or resiliency. To prevent this, be sure to wash off the sanitizer after each application.

EASY! Keep your Inertia Wave away from hand sanitizer, alcohol, salt water, chlorine, and direct sunlight over 85 degrees. (just sitting there for hours) These element will discolor or break down the polymer and may lessen the tensile strength or resiliency. Wash with warm water and soap after use.

Still have questions? 203-675-5575